Changes between Version 5 and Version 6 of PybLite

Timestamp:

Apr 13, 2024, 3:01:11 PM (8 months ago)

Author:

katta

Comment:

--

PybLite

@@ -12 +12 @@
 
 [KhoPyboard PyBoard一覧に戻る]
+
+== PybLITE1.0 動作ログ
+  * 既に、MicroPython は実装されており、USBケーブルで、接続し !TeraTerm で開く
+  * 2022/11/30 の記録
+
+{{{
+MicroPython v1.13 on 2020-09-02; PYBLITEv1.0 with STM32F411RE
+Type "help()" for more information.
+>>> help()
+Welcome to MicroPython!
+
+For online help please visit http://micropython.org/help/.
+
+Quick overview of commands for the board:
+  pyb.info()    -- print some general information
+  pyb.delay(n)  -- wait for n milliseconds
+  pyb.millis()  -- get number of milliseconds since hard reset
+  pyb.Switch()  -- create a switch object
+                   Switch methods: (), callback(f)
+  pyb.LED(n)    -- create an LED object for LED n (n=1,2,3,4)
+                   LED methods: on(), off(), toggle(), intensity(<n>)
+  pyb.Pin(pin)  -- get a pin, eg pyb.Pin('X1')
+  pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p
+                   Pin methods: init(..), value([v]), high(), low()
+  pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object
+  pyb.ADC(pin)  -- make an analog object from a pin
+                   ADC methods: read(), read_timed(buf, freq)
+  pyb.DAC(port) -- make a DAC object
+                   DAC methods: triangle(freq), write(n), write_timed(buf, freq)
+  pyb.RTC()     -- make an RTC object; methods: datetime([val])
+  pyb.rng()     -- get a 30-bit hardware random number
+  pyb.Servo(n)  -- create Servo object for servo n (n=1,2,3,4)
+                   Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])
+  pyb.Accel()   -- create an Accelerometer object
+                   Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()
+
+Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name
+Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD
+Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN
+Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)
+
+Control commands:
+  CTRL-A        -- on a blank line, enter raw REPL mode
+  CTRL-B        -- on a blank line, enter normal REPL mode
+  CTRL-C        -- interrupt a running program
+  CTRL-D        -- on a blank line, do a soft reset of the board
+  CTRL-E        -- on a blank line, enter paste mode
+
+For further help on a specific object, type help(obj)
+For a list of available modules, type help('modules')
+>>>
+}}}
+
+  * モジュール pyb を調べる
+
+{{{
+>>> import pyb
+>>> pyb.info()
+ID=4b004d00:03513431:34383038
+S=96000000
+H=96000000
+P1=24000000
+P2=48000000
+_etext=806d798
+_sidata=806d7a0
+_sdata=20000000
+_edata=2000001c
+_sbss=2000001c
+_ebss=2000627c
+_sstack=2001bff8
+_estack=2001fff8
+_ram_start=20000000
+_heap_start=2000627c
+_heap_end=2001bff8
+_ram_end=20020000
+qstr:
+  n_pool=1
+  n_qstr=3
+  n_str_data_bytes=28
+  n_total_bytes=124
+GC:
+  87360 total
+  1616 : 85744
+  1=26 2=6 m=40
+LFS free: 41472 bytes
+>>>
+>>> help(pyb.LED)
+object <class 'LED'> is of type type
+  on -- <function>
+  off -- <function>
+  toggle -- <function>
+  intensity -- <function>
+>>>
+}}}
+
+  * LED を試してみる
+
+{{{
+>>> red = pyb.LED(1)
+>>> red.on()
+>>> red.toggle()
+>>> grn = pyb.LED(2)
+>>> grn.on()
+>>> grn.toggle()
+>>> ylw = pyb.LED(3)
+>>> ylw.on()
+>>> ylw.toggle()
+>>> blu = pyb.LED(4)
+>>> blu.on()
+>>> blu.toggle()
+>>>
+}}}
+
+[KhoPyboard PyBoard一覧に戻る]