[[PageOutline]]

== PybLITE1.0
  * 2022/11/21 ステラマーチャンダイジング（Amazon）で￥3,800.-
  * Flush 512KB、CPU: STM32f411RET6

||= ボードの表 =||= ボードの裏 =||
||[[Image(PybLite10.png,200)]]||[[Image(PybLite10b.png,200)]]||

  * 画像をクリックすると拡大します
  * 添付ファイルから PybLITE10.pdf(KiCAD7)をダウンロード出来ます

[KhoPyboard PyBoard一覧に戻る]

== PybLITE1.0 動作ログ
  * 既に、MicroPython は実装されており、USBケーブルで、接続し !TeraTerm で開く
  * 2022/11/30 の記録

{{{
MicroPython v1.13 on 2020-09-02; PYBLITEv1.0 with STM32F411RE
Type "help()" for more information.
>>> help()
Welcome to MicroPython!

For online help please visit http://micropython.org/help/.

Quick overview of commands for the board:
  pyb.info()    -- print some general information
  pyb.delay(n)  -- wait for n milliseconds
  pyb.millis()  -- get number of milliseconds since hard reset
  pyb.Switch()  -- create a switch object
                   Switch methods: (), callback(f)
  pyb.LED(n)    -- create an LED object for LED n (n=1,2,3,4)
                   LED methods: on(), off(), toggle(), intensity(<n>)
  pyb.Pin(pin)  -- get a pin, eg pyb.Pin('X1')
  pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p
                   Pin methods: init(..), value([v]), high(), low()
  pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object
  pyb.ADC(pin)  -- make an analog object from a pin
                   ADC methods: read(), read_timed(buf, freq)
  pyb.DAC(port) -- make a DAC object
                   DAC methods: triangle(freq), write(n), write_timed(buf, freq)
  pyb.RTC()     -- make an RTC object; methods: datetime([val])
  pyb.rng()     -- get a 30-bit hardware random number
  pyb.Servo(n)  -- create Servo object for servo n (n=1,2,3,4)
                   Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])
  pyb.Accel()   -- create an Accelerometer object
                   Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()

Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name
Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD
Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN
Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)

Control commands:
  CTRL-A        -- on a blank line, enter raw REPL mode
  CTRL-B        -- on a blank line, enter normal REPL mode
  CTRL-C        -- interrupt a running program
  CTRL-D        -- on a blank line, do a soft reset of the board
  CTRL-E        -- on a blank line, enter paste mode

For further help on a specific object, type help(obj)
For a list of available modules, type help('modules')
>>>
}}}

  * モジュール pyb を調べる

{{{
>>> import pyb
>>> pyb.info()
ID=4b004d00:03513431:34383038
S=96000000
H=96000000
P1=24000000
P2=48000000
_etext=806d798
_sidata=806d7a0
_sdata=20000000
_edata=2000001c
_sbss=2000001c
_ebss=2000627c
_sstack=2001bff8
_estack=2001fff8
_ram_start=20000000
_heap_start=2000627c
_heap_end=2001bff8
_ram_end=20020000
qstr:
  n_pool=1
  n_qstr=3
  n_str_data_bytes=28
  n_total_bytes=124
GC:
  87360 total
  1616 : 85744
  1=26 2=6 m=40
LFS free: 41472 bytes
>>>
>>> help(pyb.LED)
object <class 'LED'> is of type type
  on -- <function>
  off -- <function>
  toggle -- <function>
  intensity -- <function>
>>>
}}}

  * LED を試してみる

{{{
>>> red = pyb.LED(1)
>>> red.on()
>>> red.toggle()
>>> grn = pyb.LED(2)
>>> grn.on()
>>> grn.toggle()
>>> ylw = pyb.LED(3)
>>> ylw.on()
>>> ylw.toggle()
>>> blu = pyb.LED(4)
>>> blu.on()
>>> blu.toggle()
>>>
}}}

[KhoPyboard PyBoard一覧に戻る]